Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateGate Company in Channelview, TX
We’re Carver Gate Repair, the gate specialist serving Channelview, and our crews work on one thing: driveway gates, pedestrian gates, and the motors that run them. Channelview is not a typical suburb. Homes here sit close to the Ship Channel corridor, where industrial fallout, heavy truck vibration, and humidity work on hinges, frames, and opener electronics harder than they do a few miles west. That changes which parts fail first and how we diagnose the job. If your gate has stopped swinging, sliding, or responding, call us at (361) 320-7104 and we’ll send a background-checked technician with a written price before any work begins.
Why Channelview Homes Are Different
Much of Channelview’s housing stock is 1960s to 1980s ranch-style homes on large lots. During the oil-boom years, a lot of homeowners added custom steel or wrought-iron driveway gates, and plenty of those gates are still in service. They’re heavy, often oversized, and many still run on original chain-drive operators that are now at the end of their service life. That’s a specific set of problems: worn chains, tired motors, sagging hinges, and racks that no longer line up.
The location adds another layer. Channelview’s proximity to the Houston Ship Channel means airborne industrial fallout settles on metal surfaces. We regularly see rust on gate frames and hinge welds that would take another decade to develop in neighborhoods further inland. Constant vibration from truck traffic on Sheldon Road and I-10 loosens bolts and shortens the life of limit switches and circuit boards. And the humid subtropical climate, with heavy rains and occasional high water from the San Jacinto River, pushes moisture into operator housings and control boards. A gate that works fine in a dry spring can fail the week after a hard rain. We troubleshoot for those specific failure patterns on every Channelview call.
Styles & brands we work with
Our Main Channelview Services
Channelview homeowners call us most for two things: a gate that has stopped moving correctly, and a motor that runs but doesn’t open or close the gate reliably. Here’s what each service involves in this area.
Gate Repair in Channelview
Most Channelview repairs involve heavier-than-average gates, and that shapes the work. We check hinge posts for movement, measure sag at the latch side, and run the operator through a full cycle before quoting anything. On older oil-boom era gates, we often find that the steel itself is sound but the hardware holding it has rusted or loosened from years of truck vibration and humid air. We quote a written price, complete the repair, and back it with a 365-day written guarantee. Details are on our Gate Repair in Channelview page.
Gate Installation in Channelview
New gate work here means building for the soil and the atmosphere, not just the style of the house. Clay soil in parts of Channelview expands and contracts through flood-and-drought cycles, so a properly set post matters more than anything else on the job. We plan for drainage, use hardware rated for corrosive air, and match the gate weight to an operator that can handle it. We do not push the cheapest opener on a heavy custom gate. If you’re replacing an old gate or adding one where none existed, see Gate Installation in Channelview for a full breakdown.
Gate Motor Repair in Channelview
Motor failures in Channelview follow patterns we know well: moisture inside the operator housing, corroded limit switch contacts, and circuit boards damaged by power surges during storms. We open the unit, diagnose the specific failure, and show you the written price before we replace anything. We service operators from LiftMaster, FAAC, BFT, and Linear, and we stock common parts for those brands. The full scope is on our Gate Motor Repair in Channelview page.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Brands We Service in Channelview
Our technicians work on LiftMaster, FAAC, BFT, and Linear operators, among others. We stock common boards, limit switches, and remotes locally so most Channelview repairs are completed in a single visit. For a full list of what we service, see our brands.
See the difference
Before
After
Before
After
Before
AfterPricing for Gate Company in Channelview, TX
| Service | Typical range in Channelview |
|---|---|
| Gate repair, minor (hinge, latch, alignment) | $150 – $350 |
| Gate repair, major (rack, weld, frame section) | $350 – $900 |
| Gate opener motor replacement | $450 – $1,200 |
| Control board replacement | $250 – $600 |
| Limit switch replacement | $120 – $300 |
| Remote or keypad programming | $75 – $200 |
| Chain or belt replacement on opener | $150 – $350 |
| Full gate installation (single swing) | $2,500 – $6,000 |
| Full gate installation (sliding, heavier) | $4,000 – $9,000 |
| Operator installation (new build) | $1,500 – $4,000 |
What pushes a Channelview job toward the higher end of those ranges is weight and corrosion. An oversized steel gate with rusted hardware takes longer to work on than a standard aluminum one, and a motor that has been soaking in humid air for ten years may need more than a single part swapped. Whatever the job, you get a written price agreed before any work starts. The number does not move at the door.
Neighborhoods We Serve in Channelview
We run calls across the whole Channelview area, from the neighborhoods near Sheldon Road east to the San Jacinto River and south toward I-10. Depending on where you are, our typical response for a gate repair call is same-day or next-morning, and we schedule a window you can plan around.
- Old River Terrace
- Clover Leaf
- Sheldon Woods
- River Terrace
- East Houston (Channelview side)
Service Area – Cities Near Channelview
We also cover surrounding communities along the I-10 and Highway 90 corridors. If you’re across the river or just down the freeway, you can find us in Highlands, TX, Deer Park, TX, Baytown, TX, or Houston, TX.
Serving Channelview, TX - Our Local Coverage Area
We’re based in the Channelview area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Gate Company in Channelview
For repair calls in Channelview, we typically arrive the same day or the next morning depending on where you are and when you call. Phone lines are answered by a live person around the clock, so you get a real answer on scheduling any hour, any day. Call (361) 320-7104 and we’ll give you an arrival window before we hang up.
Most gate repairs do not need a permit. New installations, especially anything involving an operator and electrical work, may require one depending on the scope and your property. If a permit is needed, we’ll tell you during the estimate so there are no surprises on inspection day.
Yes. A lot of Channelview properties sit on large lots, and many have oversized driveway gates built years ago. We work on those regularly, including heavy steel and wrought-iron gates with older operators. We quote the job on site and in writing before any work is done.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Channelview Customers Say
"Good repair on a motor board. Waited a few days on the part, but they stayed in contact."
- Shelby T."Straight answers on whether to repair or replace the operator. Repair was the right call."
- Wanda F."Keypad and remotes set up fresh for the whole neighborhood. Done cleanly and quickly."
- Chris W.