Linear Gate Installation Nationwide

Linear Gate Installation in Houston: What to Know First

Linear gate installation in Houston typically runs $1,450 to $4,800 depending on gate size, motor type, and site preparation. Most residential Linear installations we quote are completed within 5 to 10 business days after the written price is approved. As an independent Linear service provider, we install and service the full range of Linear residential and light commercial operators, and every job starts with a written price before any work begins.

Call (361) 320-7104

This page is for Houston homeowners who have a Linear gate opener either already purchased or spec’d for their property, and want a crew that actually knows the equipment. If you’re weighing Linear against another brand, or you’ve got a Linear unit sitting in the box in your garage, call (361) 320-7104 and we’ll talk through what you’re working with. The estimate is free.

How Linear Products Fail – and How We Fix Them

Linear operators are common across Houston, and after well over a decade of installing and repairing them, we know their failure patterns. Here are the ones we see most often on installs and replacements.

• Linear LDO series limit switch drift. The LDO50 swing operators use mechanical limit switches that can shift a few degrees over time, especially on gates that get bumped by wind or kids. The gate starts short-stroking or over-traveling and the motor keeps running against the stop. We re-set the limits, then tighten the cam screws with thread locker so they hold. On gates exposed to constant Houston wind, we’ll recommend a magnetic limit upgrade that doesn’t drift.
• Linear APeX control board No. 1 problem: dead battery-backed logic. The APeX board in Linear’s slide operators fails quietly after power surges, which Houston gets plenty of during thunderstorm season. The gate still opens on the manual release, so homeowners don’t realize the board is fried until the remote stops working. We test the board before ordering any parts, because a dead transformer and a dead board can look identical on a multimeter.
• Corroded plug-in loop detector sockets. Linear operators with plug-in loop detector modules suffer from Houston humidity. The pins on the detector card oxidize just enough to throw intermittent obstruction faults, and the gate reverses for no visible reason. We clean the socket with contact cleaner, reseat the module, and apply a thin dielectric coating. That fix holds for years in most Houston applications.
• Mighty Mule, Ghost Controls, and DoorKing retrofits mixing with Linear hardware. When homeowners swap a Mighty Mule or Ghost Controls opener for a Linear operator, they often reuse the old receiver, keypad, or photo eyes. Linear’s control boards don’t always play nice with third-party accessories over time, particularly Ghost Controls wireless keypads. We flag compatibility before the install, not after, so you don’t end up with a gate that works for a week and then starts ghost-opening at 2 a.m.
• Undersized operators on oversize Houston gates. This is the most common install failure we see: a Linear LSO75 slide operator on a gate that’s 40 feet long and sheathed in cedar. The motor works, but it’s working too hard, and Houston heat finishes the job on the capacitor within two summers. We size the operator to the actual gate weight and wind load, not the brochure’s “up to” number. A properly sized Linear operator on a heavy gate should run cool to the touch after a full cycle.

Our Linear Gate Installation Process

Every Linear job follows the same sequence, whether it’s a new driveway gate in Meyerland or a replacement swing operator out near Katy.

1. 1
   Site call and measure. We measure the gate, the posts, the setback, the paving, and the power run. We also check what’s already in the ground: existing conduit, loop wires, low-voltage cable.
2. 2
   Written price. Before we leave, you get a written quote that itemizes the operator, the hardware, the labor, and any electrical. That number does not move unless we find something we agreed in writing to address.
3. 3
   Parts decision. For Linear installs, we default to OEM Linear parts when the warranty matters and the availability is there. For discontinued boards or power supplies, we’ll source quality aftermarket replacements and tell you the tradeoff in plain terms before you pay for anything.
4. 4
   Installation. We mount, wire, and set the limits. We run a full obstruction test on both opening and closing cycles, check the force settings against the gate’s actual weight, and confirm the auto-close timing if you want it.
5. 5
   Cleanup and walkthrough. We clean the site, haul any old hardware, and walk you through the remotes, keypad, and manual release. If the manual release is hard to find or hard to pull, we show you before we leave.
6. 6
   Written guarantee. Your guarantee is in writing, good for a full year. If the install fails inside that window, the second visit is free. No charge, no argument.

What Linear Gate Installation Costs in Houston

Here are the ranges we quote most often for Linear work in Houston. These are installed prices including labor and basic electrical, assuming the site has power within a reasonable run.

• Linear LSO75 slide operator on an existing gate: $1,850 – $2,600 (operator, mounting, wiring, one remote, safety photo eyes)
• Linear LDO50 swing operator on a single gate: $1,450 – $2,200 (includes articulation arm and dual remotes)
• Full driveway gate plus Linear operator: $3,200 – $4,800 (fabricated steel gate, track or v-wheels, operator, keypad, loop detector)
• Heavy-duty linear slide operator for commercial gates: $3,800 – $6,500 (depends on gate weight, duty cycle, and access control add-ons)

What moves the price: gate weight, post condition, the power run distance, and whether you want a loop detector or just photo eyes. We quote the number before any work starts, and if we think a repair on your existing Linear unit is the smarter money, we’ll tell you that instead of selling you an install. Call (361) 320-7104 for a free estimate on your specific gate.

Why Houston Homeowners Call Carver Gate Repair Houston for Linear Work

Homeowners in Houston call us because they’ve already had a bad experience with a gate tech who didn’t show, or didn’t know what was wrong, or quoted one number and billed another. That’s what we built Carver Gate Repair Houston to fix. We work to The Garrison Standard, which is a specific set of rules, not a slogan: written prices, background-checked and uniformed technicians on every call, and the 365-Day Done Right Promise. The guarantee is in writing on every repair and every install, good for a full year from the date of service.

Lonnie Burke runs the Houston operation. He learned the mechanical side of things early and completed a welding and fabrication program at Los Angeles Trade-Technical College before moving full time into gate and access systems. He’s been repairing and installing gates across Houston for well over a decade, from residential slide gates in Meyerland to commercial swing gate systems along the ship channel corridor. When a Linear operator shows up with a problem, Lonnie diagnoses it correctly the first visit. As he puts it: “If I can’t tell you exactly what’s wrong before I order a part, I shouldn’t be charging you for the part.”

And if the day ever comes when a Linear unit isn’t the right fit for the job, we’re trained on the other major brands too: LiftMaster, Mighty Mule, Ghost Controls, and DoorKing. We match the equipment to the gate, not the other way around.

FAQs