Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateStyles & brands we work with
See the difference
Before
After
Before
After
Before
AfterHow Much Does Gate Repair Cost in Houston?
Gate repair in Houston typically runs between $180 and $650 for most mechanical and electrical fixes, with motor replacements landing between $450 and $1,500 depending on the brand. Emergency service and heavier structural work on steel driveway gates can push the total to $1,000 or more. This guide breaks down what you’ll actually pay in the Houston market in 2026, so you can compare quotes with numbers in hand. For a detailed breakdown, see our How Much Does Gate Repair Cost in Houston, TX? (2026 Price Guide).
Gate Repair Cost Breakdown (2026)
Here are the line items we quote most often in Houston, from Bellaire to Cypress to Clear Lake. Prices include labor and standard parts unless noted.
| Repair Type | Typical Cost Range (Houston, 2026) | What It Covers |
|---|---|---|
| Gate won’t open or close (diagnostic + minor fix) | $95 – $180 | Limit switch adjustment, photo eye realignment, remote reprogramming, or loose wiring |
| Gate off track (sliding gates) | $150 – $400 | Track straightening, roller replacement, or guide wheel service |
| Hinge replacement (swing gates) | $120 – $300 per hinge | Heavy-duty hinge removal and replacement on steel or iron gates |
| Control board replacement | $250 – $600 | New circuit board matched to the existing operator |
| Gate motor / operator replacement (single swing) | $450 – $1,200 | New operator, labor, and basic programming |
| Gate motor / operator replacement (sliding) | $600 – $1,500 | New sliding gate operator, chain or belt, and labor |
| Loop detector installation or replacement | $200 – $450 | Vehicle detection loop and new detector module |
| Keypad or intercom replacement | $150 – $500 | New entry keypad, card reader, or phone intercom wired to the operator |
| Welding repair (steel or wrought iron) | $150 – $600 | On-site weld repair for cracked posts, broken pickets, or sagging frame |
| Full driveway gate installation (double swing) | $3,500 – $9,000 | New steel gate, operator, concrete work, and electrical |
What moves the number in one direction or the other? First, the gate’s size and weight. A 16-foot solid steel driveway gate puts far more strain on the motor than a 6-foot pedestrian gate with aluminum construction. Second, the operator brand. LiftMaster and Mighty Mule parts are widely available and priced lower than FAAC or Viking components, which are often special-order in Houston. Third, site conditions. A gate post that has shifted in Houston’s expansive clay soil often requires concrete resetting before a motor can be aligned correctly, and that adds labor.
We give a written price before any work starts. That’s not a courtesy; it’s The Garrison Standard. The number on the quote is the number you pay. If the scope changes mid-job, you approve a new written price before we pick up a tool.
What Affects Gate Repair Pricing in Houston
Houston’s specific conditions change what gate repairs cost here versus, say, Dallas or Austin. Here’s what moves the needle.
- Clay soil and gate post movement. Houston sits on expansive gumbo clay that swells after rain and cracks during droughts. Gate posts shift, which throws off hinge alignment and stresses motors. Repairs often include digging out and resetting posts in new concrete, which adds $100 to $300 per post.
- Humidity and control board corrosion. Southeast Texas humidity shortens the life of circuit boards and electrical connections, especially on gates facing morning sun with heavy condensation. Control board failures are among our most common calls from Katy and Sugar Land.
- Operator brand and parts availability. We work on nine brands: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. LiftMaster and Mighty Mule parts are stocked in Houston. FAAC and Viking boards often have to ship from a distributor, which can add two or three days and $50 to $100 in freight.
- Gate size and construction. Solid wood and steel gates weigh more than aluminum or ornamental iron. A heavier gate needs a stronger operator, and if the operator is undersized for the gate, you’ll replace it sooner than you should. The right match matters.
- Access to power and the operator. Many Houston homes built before the 1990s have driveway gates with outdated or inadequate electrical runs. If the repair requires a new conduit run or a dedicated circuit, the electrician’s portion adds $150 to $500.
- Water exposure and flood zones. In neighborhoods like Meyerland and parts of Kingwood, gates sit in flood-prone yards. Water intrusion into the operator housing or junction boxes accelerates corrosion. Below-ground loop detectors also fail faster after repeated saturation, which means more frequent loop replacement.
None of these factors should come as a surprise on the day of service. A technician who explains the cause before quoting the fix is doing the job correctly. At Carver Gate Repair Houston, every technician is background-checked and uniformed, and every quote is written down before work begins. If you’re searching for Gate Repair Near Me in Houston, TX, we cover the full metro area. You know the cause, the cost, and the crew before the truck pulls away.
How to Save on Gate Repair
Gate repair is not a place to chase the lowest bid. A cut-rate motor installation that fails in six months costs more than a proper fix done once. But there are legitimate ways to keep the total down without cutting corners.
- Fix small problems before they take out the motor. A gate that scrapes the ground or sticks mid-cycle forces the operator to work harder. A hinge repair at $150 beats an operator replacement at $800, and the warning signs are there before the motor gives out.
- Ask for a written diagnosis first. Some companies charge a diagnostic fee, some roll it into the repair. At Carver, you get a written price for the full job before any work starts. There’s no “wait and see” pricing at the door.
- Keep up with basic lubrication and cleaning. Houston’s dust and humidity gum up rollers and hinges quickly. Twice a year, wipe down the track and lubricate moving parts with a silicone-based spray. It costs $15 and can prevent several hundred dollars in wear-related repairs. (Leave spring and motor work to a technician; those carry tension and voltage you don’t want to learn about by accident.)
- Don’t ignore the photo eyes. When a gate reverses for no reason, the photo eyes are often misaligned or dirty. Cleaning the lenses with a dry cloth and making sure they’re pointed at each other fixes a surprising number of “the gate won’t close” calls. If realignment doesn’t do it, call us at (361) 320-7104 and we’ll diagnose over the phone.
- Use a company that guarantees the work in writing. The cheapest repair is the one you don’t pay for twice. Carver Gate Repair includes a 365-day written guarantee on every repair. If the fix fails inside that year, the second visit is free. No charge, no dispute, no “that’s not covered.”
Get a free estimate before you commit to anything. Call (361) 320-7104 and a live person answers, any hour of the day. You’ll get an honest range over the phone and a written price before the work starts.
Frequently Asked Questions About Gate Repair Cost in Houston
How much does it cost to repair a gate motor in Houston?
Most gate motor repairs in Houston run between $180 and $650. Replacing the entire operator runs higher, typically $450 to $1,500 depending on whether it’s a swing or sliding gate and which brand is installed. If you can tell us the brand and the symptom, we can usually narrow that down over the phone. Call (361) 320-7104 for a free estimate.
Is it cheaper to repair or replace a gate?
For most repairs, fixing is cheaper: a hinge, board, or keypad replacement runs $150 to $600, while a new driveway gate starts around $3,500 and goes up from there. Replace when the gate frame is rusted through in multiple places or the operator is more than 12 years old and parts are discontinued. We’ll tell you which makes sense, in writing, before any work is done.
Why did my gate stop working after a storm?
Houston storms cause three common failures: water in the operator housing, a tripped GFCI outlet, or a lightning strike on the control board. The fix ranges from $95 (reset and inspection) to $600 (board replacement). After heavy rain, check the outlet first; if the breaker is set and the gate still won’t move, call us.
How much does a loop detector replacement cost in Houston?
Replacing a loop detector on a Houston driveway gate typically costs $200 to $450, including the detector module and labor. If the buried loop wire itself is damaged, saw-cutting and replacing the loop adds $150 to $350. Flood-prone yards in Meyerland and along the bayous see loop failures more often than other parts of the city.
Do you charge extra for emergency gate repair?
Our phone is answered by a live person 24/7, including weekends and holidays, and we don’t charge a separate “emergency fee” for off-hours calls. You pay the same written price whether it’s Tuesday afternoon or 2 a.m. The technician gives you a written quote before the work starts, every time.
How long does a typical gate repair take?
Most hinge, limit switch, keypad, and photo eye repairs take 45 minutes to 2 hours on site. Motor replacements run 2 to 4 hours, and full gate installations are scheduled as a full day. We’ll give you an arrival window when you call and a realistic timeline for your specific repair before we start.
How the Repair Process Works at Carver Gate Repair Houston
You’ve been through the routine before: a technician gives you a vague estimate, then the price climbs once the work is open. That’s the exact experience The Garrison Standard was built to eliminate. Here’s how it goes with us.
- Call or message us. A live person answers at (361) 320-7104, day or night. We ask for the gate type, the operator brand if you know it, and the symptom. That lets us arrive with likely parts already on the truck.
- We arrive in a marked vehicle, in uniform. Every technician is background-checked and wears Carver identification. You know who’s at the gate before you open it.
- Written diagnosis and written price, before any work. The technician inspects the gate, tells you what’s wrong in plain language, and hands you a written price. No verbal estimates, no “we’ll see how it goes.”
- You approve the work. The price on the sheet is the price on the invoice. If something changes mid-repair, we stop and get your approval on a new written number.
- The repair is done and the site is clean. We haul off old parts and leave the gate operating correctly. Then we walk you through what we fixed and what to watch for going forward.
- You get the 365-Day Done Right Promise in writing. Every repair includes a full-year guarantee. If something we fixed fails within 12 months, the second visit is free. That guarantee has been part of The Garrison Standard since 2008.
This process applies to every job, from a $95 limit switch adjustment in Cypress to a $9,000 double swing installation in River Oaks. The standard doesn’t change with the invoice total.
What Gate Brands We Repair and Install
Gate motor repair is not generic work. A Viking operator has different logic than a Mighty Mule, and a FAAC hydraulic swing arm handles differently than a LiftMaster belt drive. Our technicians are trained across nine brands specifically because Houston neighborhoods have everything installed. Here’s the full list:
- LiftMaster – Common in newer subdivisions; parts are affordable and stocked fast.
- FAAC – Hydraulic operators found on higher-end estates; parts are pricier and often special-order.
- BFT – Italian-built operators common in gated communities; board failures are the usual culprit.
- Linear – Found on many mid-market driveway gates; reliable but aging fast in Houston humidity.
- Viking – Heavy-duty slide operators for large commercial-style residential gates.
- Ghost Controls – DIY-installed systems that often need professional correction when the gate drifts off track.
- DoorKing – Long-running brand for swing and slide gates; parts remain available for older models.
- Elite – Slide gate operators with a reputation for durability; photo eye alignment issues are common.
- Mighty Mule – Budget-friendly operators on many smaller gates; control boards fail more often in humid conditions.
If your gate motor isn’t on this list, call anyway. Odds are we’ve worked on it, and if we haven’t, we’ll tell you honestly before scheduling the visit.
Houston Neighborhoods We Serve
Carver Gate Repair Houston covers the full metro area, including Bellaire, West University, Meyerland, Katy, Sugar Land, Cypress, Spring, The Woodlands, Kingwood, Humble, Pearland, Clear Lake, League City, and Pasadena. Gates in Katy’s newer developments tend toward LiftMaster and Mighty Mule installations, while River Oaks and Memorial homes often run FAAC or Viking operators on heavier steel gates. The soil under your gate posts matters to the repair, and so does knowing which neighborhoods sit on the worst clay: the northwest corridor from Cypress down to Katy consistently shows more post settlement than the sandier soils near Clear Lake.
This local knowledge is why we don’t send a general contractor to fix your gate. We send a gate technician who knows what Houston soil, Houston humidity, and Houston storms do to gates. And when you call, a person in Houston picks up.
Get a Free Gate Repair Estimate in Houston
You don’t need to know exactly what’s wrong with your gate before you call. Describe the symptom: is it not opening, opening halfway, reversing before it closes, or grinding when it moves? A live person at (361) 320-7104 will listen, ask a few questions, and give you a realistic cost range for your situation. The estimate is free, the written price is guaranteed before work begins, and the repair is covered by our 365-day guarantee. That’s the standard Lonnie Burke and the Carver Gate Repair Houston crew work to on every single Gate Repair job, no exceptions.
Pricing reflects the Houston market as of 2026. Carver Gate Repair Houston offers free estimates – call (361) 320-7104.
Written by Lonnie Burke, Owner at Carver Gate Repair Houston, serving Houston since 2008.
What Our Customers Say
"Keypad and remotes set up fresh for the whole neighborhood. Done cleanly and quickly."
- Chris W."Swing gate arm snapped. They replaced the actuator and tested the safety reverse. Fair price."
- Angela P."Slide gate wasn't opening fully. Veteran tech found a worn drive chain and a misaligned limit. Fixed both in one visit."
- Don H.